FDA approves more meat additives

By Ahmed ElAmin

- Last updated on GMT

Related tags Citric acid Vinegar Food Food and drug administration

The federal food safety inspection unit has approved an additional
batch of additives, antimicrobals and agents for use as processing
aids directly on meat and poultry products.

The updated list adds more substances that can be used during meat and poultry processingoperations, giving more options in the food safety arsenal available to processors. The newapprovals were made since the list was last updated on 10 May 2006.

Increased food safety regulations and the cost of recalls due to contaminated foods are driving processors to search for better solutions to reduce pathogens in their plants.

Food and Drug Administration's (FDA) regulationsdefine processing aids as substances -- such as an organic cleaning acid -- that are required during the manufacture or processing of a food andthat are ordinarily removed from the final food. Although residuals might carry over to the final food, residuals must nothave any health effect. Other additives may be used to provide a technical effect in the final food,such as the antioxidants BHA and BHT.

Naming the additive used is not required on the label. The FDA's Food Safety and Inspection Service(FSIS) classifies all such substances as acidifiers, anticoagulants,antimicrobials, antioxidants, binders, coloring agents, curing accelerators, denuding agents, filmforming agents, flavoring agents, poultry scald agents, and packaging system agents.

A new addition to the range of antimicrobial agents is a blend of citric acid and sorbic acid in a2 to 1 ratio. The mix has been approved for use in reducing the microbial load of purge trapped inside soaker pads in packages of raw whole muscle cuts of meat and poultry.It may be incorporated into soaker pads at a level not to exceed 1 to 3 grams per pad.

The FSIS has also approved the use of citric acid as an antimicrobial agent on separated beef heads andoffal. It may be used at a 2.5 percent solution applied as a spray prior to chilling. Lactic acidhas also been approved for use as a 2 to 2.8 percent solution applied to brushes in a washer cabinet system used to clean beef heads and tongues.

Lauramide arginine ethyl ester has been approved for use on ready-to-eat ground meat products,such as sausages, that permit the use of any safe and suitable antimicrobial agent. A residuemaximum limit has been set at 200 ppm by weight of the finished product.

A 60 to 40 blend of sodium bicarbonate and citric acid has been approved for use in generating carbon dioxide in packages of raw whole muscle cuts of meat and poultry.The blend must be incorporated into soaker pads at a level not to exceed 0.5 to 2 grams per pad.

Trisodium phosphate has been approved as a component of phosphate blends, not to exceed 40 percent of themix. It may be used to decrease the amount of cooked out juices in meat food products except where otherwise prohibited by the meatand poultry inspection regulations

For meat food products, processors are allowed to use 5 per cent of phosphate in pickle at a 10 percent pumplevel. It can also be used as 0.5 percent of phosphate in meat food product. Only clear solution may be injected intothe meat food product. For poultry food products, the FSIS has approved its use as 0.5 percent ofthe total product.

The introduction of novel and value-added products and additive free foods is boosting the use of antimicrobials in almost all food processing segments, according to a report last year from Frost & Sullivan.

The analyss forecasts that US demand for antimicrobials -- chemicals used to wash equipment and foods to ensure they are free of food borne pathogens -- will reach $215.8m in 2012, from $161.7m in 2005.

The market segments demanding more and more antimicrobials include dairy, bakery, beverages, and meat processors.

Related news

Show more

Related products

show more

White Paper: Solving for Sugar Reduction

White Paper: Solving for Sugar Reduction

Content provided by ADM: Innovation that Feeds the Future | 02-Nov-2023 | White Paper

Sugar does more than provide sweetness. It is a foundational ingredient, contributing to texture, color, and mouthfeel while also providing the necessary...

Injection Molding Solutions: Key Considerations

Injection Molding Solutions: Key Considerations

Content provided by Husky Injection Molding Systems Ltd. | 27-Sep-2023 | Insight Guide

Food and consumer packaged goods (CPG) producers are now facing a number of new challenges and opportunities.

These include the rising adoption...

Related suppliers

Follow us

Products

View more

Webinars